How to Rebuild and Repair a Hiblow Septic Aerator

0
580

 Why is the Alarm Going off on my Hiblow Septic Aerator?

The alarm of your septic control unit is buzzing, and the warning light is flashing.
Your Hiblow aerator has suddenly stopped working.
Before you purchase a replacement, you should consider rebuilding your existing Hiblow aerator using a repair kit.
Hiblow septic air pumps typically stop working when one of the diaphragms tear.
The air pump is designed with a safety screw that breaks when the magnet travels too far due to the diaphragm rupturing to prevent further damage to the aerator. 

This Tutorial

This tutorial will provide a step-by-step process of rebuilding a Hiblow aerator using a rebuild kit.
In this demonstration, we will be using the Hiblow HP-60/80 rebuild kit. However, the process is the same for any model of Hiblow aerator.
This process is also the same for other linear diaphragm pumps due to them having similar design layouts and working methods.  

Step 1: Gather Tools and Materials 

You will need these items below to rebuild your aerator.
A chart is provided below to match up your Hiblow model number with the proper repair kit in our store.

Hiblow Repair


What you will need:

The damaged aeratorPhillips screwdriver

5/16 or 8mm socket wrench
7mm for the diaphragm nut/washer
A repair kit for your aerator

Your repair kit should have the following replacement parts:

two chamber blocks
2 diaphragms
Dust filter
Nuts and washers for the diaphragm
Replacement safety screw


Below is a chart to help you find a repair kit for your aerator:

Hiblow ModelRebuild/Repair Kit
HP-30HP-30 Rebuild/Repair Kit
HP-40HP-40 Rebuild/Repair Kit
HP-60HP-60 Rebuild/Repair Kit
HP-80HP-80 Rebuild/Repair Kit
HP-100HP-100 Rebuild/Repair Kit
HP-100LLHP-100LL Rebuild/Repair Kit
HP-120HP-120 Rebuild/Repair Kit
HP-120LLHP-120LL Rebuild/Repair Kit
HP-150HP-150 Rebuild/Repair Kit
HP-200HP-200 Rebuild/Repair Kit

Step 2: Remove corner bolts

Locate and remove the four bolts on each corner of the aerator using the 8mm wrench or the Philips screwdriver.
This will usually be easier using the wrench because the insides of the screws may be rusted or have dirt in them.
Using the screwdriver may run the risk of stripping the screw.
Don’t panic if this happens; you can still use a socket wrench to remove the bolts.

Hiblow Repair
Hiblow Repair

Step 3: Remove top cover

Remove the green cover form the base of the aerator.
This reveals the insides of the aerator.
You might have to tap lightly on the edges with a hammer or mallet to loosen the cover.

Hiblow Repair


Step 4: Remove the Fire-Resistant Sound-Insulating Shroud

Remove the rectangular sound insulating shroud that is wrapped around the unit.
This will be tightly fit around the aerator.

Hiblow Repair


Step 5: Remove chamber block screws

Locate the two chamber blocks on the ends of the aerator.

Hiblow Repair


 Use the Philips screwdriver to remove 8 total screws from both chamber blocks.

Hiblow Repair

Step 6: Remove Chamber Blocks

Once the screws are removed, remove the chamber blocks to expose the diaphragms.
To do this, you will need to detach them from the rubber air tubes.
Be sure to detach the chamber blocks from the tubes after the blocks are unscrewed. 
Twist the chamber blocks back and forth to accomplish this, do not pry at the rubber air tubes, as you run the risk of tearing the rubber.

Hiblow Repair

Step 8: Remove Nuts and Washers

Use the 7mm wrench to remove a nut and washer located in the center of each diaphragm.

Hiblow Repair

Here is the second diaphragm below.

Hiblow Repair


Step 9: Remove Diaphragms

Remove the old diaphragms.
You will have to remove both diaphragms before inspecting the magnet in the next step.

Hiblow Repair


Step 10: Check Magnetic Rod Block

Remove and inspect the magnet in between where the two diaphragms were.

Hiblow Repair

You should be looking for any cracks in the housing, or if the threads that were attached to the diaphragms are broken. These issues may happen if the safety screw does not function properly.

If your magnet is damaged, you should purchase a replacement magnet before continuing the rebuild. 
If you don’t spot any issues, replace the old magnet back into the aerator.
If your aerator has a lot of red dust inside, It is advisable to replace aerator due to the fact the coils are breaking, which is a sign your aerator doesn’t have much more life left.

Step 10: Replace Diaphragms

Put the new diaphragms on where the old ones used to be. Replace both diaphragms before replacing the chamber blocks.
Secure the new diaphragms using the replacement nuts and washers from the kit. 
You will have to push into one of the diaphragms after replacing the first one so that the threads on the magnet stick out to replace the second diaphragm, as pictured below. 

Hiblow Repair


Pushing on one side of the diaphragm.

Hiblow Repair
Hiblow Repair

Step 11: Replace Chamber Blocks


Place the replacement chamber blocks onto the diaphragms. 
Screw in the chamber blocks using the 8 screws that were removed in step 5. 
Be sure to secure the air tubes to the chamber blocks using the metal sealing clamps. The sealing clamps should be pointed upwards so that the shroud will fit back on correctly. 

Hiblow Repair
Hiblow Repair

 Step 12: Replace Safety Screw

Locate the broken safety screw on top of the aerator

Hiblow Repair


Insert the replacement safety screw through the two copper connectors. Make sure that the screw head is inserted on the other side of the copper connecters so that the white nylon nut can be threaded on correctly. 

Hiblow Repair


Once the screw is in place, take the white nylon nut to the end of the screw and tighten until the copper connectors are closed. 

Hiblow Repair


There is a space between the threads of the screw where it is smooth. The nylon nut only needs to be placed up to here.

Hiblow Repair

Step 13: Replace Shroud

Replace the rectangular shroud that was removed in step 4.
Remember that the sealing pins on the air tubes need to be facing up for you to adequately replace the shroud. 

Hiblow Repair

Step 14: Replace Cover

Replace the aerator cover and corner bolts 

Hiblow Repair

Step 15: Replace Air Filter

Use the Phillips head screwdriver to remove the top of the cover

Hiblow Repair
Hiblow Repair


Replace the old filter with the replacement from the kit 

Hiblow Repair


Screw the top of the aerator back on

You’re now finished

You have successfully rebuilt your Hiblow Aerator

If you would like more information about Hiblow rebuild kits, please visit https://aerobicsepticsystem.com where we post tips, tricks, and other great information!

LEAVE A REPLY

Please enter your comment!
Please enter your name here